Antenna Tuner for Receiving Antennas MFJ-959C |
Don't
miss rare DX due to signal power loss between your receiver and antenna. The
MFJ-959C provides proper impedance matching so you can transfer maximum signal
from antenna to receiver.
It covers 1.6 to 30 MHz. 20 dB preamp with gain control boosts weak stations. 20
dB attenuator prevents overload. Select from 2 antennas and 2 receivers. It
measures 9 x 2 x 6 inches. Required power supply 9-18 VDC.
Order No. | ||
---|---|---|
MFJ-959C | Antenna Tuner with Preamp. | 159.00 |
PL-cable |
PL-cable for connecting the preselector to the receiver(s). Low loss cable, both sides PL-Plug, only 5.5mm diameter.
Order No. | ||
---|---|---|
40402.50CM | PL-cable, 0.5m | 10.30 |
40402.01 | PL-cable, 1.0m | 10.90 |
40402.02 | PL-cable, 2.0m | 12.50 |
Discone |
Discone
antennas are vertically polarized wideband antennas with omni directional
pattern. The frequency range is 75 to 900 MHz; the antenna can be used for
transmitting from 100 to 500MHz with reasonable SWR. Height approx. 85cm,
connector PL. Discone antennas work principally as a vertikal dipol. The Gain is
0 dBd or 2 dBi.
U-bracket for pole mounting allow mast diameter from 25 to 52mm.
Order No. | ||
---|---|---|
18060 | 65.50 |
AOR DA-3200 dicone 25- 3000 MHx |
The
AOR DA3200 is a 16 element (stainless steel), base, omnidirectional discone
receiving antenna covering 25 to 3000 MHz. The antenna is approximately 45
inches tall (1.12m). It comes with two U bolts to mount the antenna to a mast (not
included). It includes 49 feet (15 m) of low-lose 5D-2V 50 ohm coax lead-in.
This supplied lead-in features an N male plug for the antenna end and now
an N male plug for the radio end. (A plug change or adapter will be required for
other radios with BNC or PL259 antenna input - see optional adapters below).
This robustly built antenna has rated wind velocity of up to 112 MPH. (Mast
shown is not included). Please note that this antenna is not for transmit
applications.
Click here to view specification sheet [PDF 241K].
Order No. | ||
---|---|---|
AOR DA-3200 | 185.00 |
AOR SA-7000 twin elements antenne 30 kHz-2000 Mhz |
The
AOR SA7000 super wide range receiving antenna covers from 30 kHz to 2 GHz. This
6 foot (1.8 m) passive antenna has two vertical elements with a built-in
duplexer. The aerial is designed for areas where space is a problem or when an
unobtrusive installation is essential. The SA7000 is a passive arrangement
providing two whip elements: a long element for short wave up to 30 MHz and a
second shorter loaded whip aerial for frequencies up to 2 GHz, the loading coils
are tuned around 150 and 800 MHz to enhance performance of the VHF and UHF
bands. A single coaxial lead feeds both whips in a weather proof enclosure which
in turn bolts to a suitable supporting mast (not provided).
The SA7000 is easy to assemble and use, an instruction sheet is supplied with the aerial, "V" bolts and clamps are included but a small stub mast will be required for installation which should be as high as possible and in clear space. This antenna includes 50 feet of RG-58 coax lead-in with a PL-259 to plug into the antenna base and a 50 ohm BNC plug to go into the radio.
Click here to view SA7000 spec sheet [PDF 149K].
Order No. | ||
---|---|---|
AOR SA-7000 | 259.00 |
AOR DA-5000 prof dicone 700-3000 MHz |
Do
you want to start neighborhood rumors about yourself? Just put an AOR DA5000 on
your roof. It may look like Darth Vader's TV antenna, but this is
actually a very high performance, commercial grade UHF discone receive antenna
covering 700 to 3000 MHz. This antenna employs a low-loss N connector. Antenna
gain is 2.5 dB (max.). Overall length is 1 foot. Radials are 5.7 inches.
Horizontal elements are 3.2 inches. Weight is 1.6 lbs. Impedance is 50 ohms.
Very low loss coaxial cable (not supplied) must be used with this antenna. The DA5000 comes with a mounting mast, mast clamp and instructions. Will fit over a mast between 1 and 2 inches diameter.
Order No. | ||
---|---|---|
AOR DA-5000 | 334.00 |
DIAMOND D-130J / D-190 / D-3000 Discone |
The
Discone antenna is the most suitable form for a wide band omni-directional
antenna. It is used by military as well as other commercial services worldwide.
The Diamond Discone antenna use stainless steel for most parts, the construction
is very solid. This ensures a reliable operation for many years. The Diamond
discone antennas are suitable for transmission with the VHF/UHF amateur bands
and can replace or complement the usual staion antennas.
The D-130J works for reception from 25 – 1300 MHz, transmit.wise it's useable on 6m, 2m, 70cm and 23cm, with limitations also on 900MHz /GSM). This antenna is available with PL or N socket.
The model D-190 is designed for a higher frequency range, from 100 to 1500 MHz. This makes the antenna somewha tsmaller and less visible. Transmission is possible on 2m, 70cm and 23cm, partially with rteduced power up to 30W only. See data sheet. This antenna comes with a PL female socket and 10m RG-58 cable with PL connectors on each end.
The Diamond D-3000 Discone is used for reception from 25 – 3000 MHz, transmit on 6m, 2m, 70cm and 23cm. Connector is N female.
Order No. | ||
---|---|---|
18061 | Diamond D-130J Discone 25-1300MHz, PL socket | 95.00 |
18061.N | Diamond D-130NJ Discone 25-1300MHz, N socket | 93.00 |
18062 | Diamond D-3000 Discone 25-3000MHz, N socket | 129.00 |
18063 | Diamond D-190 Discone 100-1500MHz, PL socket, 10m Cable | 86.00 |
Download: D-3000 Mounting
Instructions (18062) (PDF, EN, 740KB)
Download: D-130J Mounting
Instructions (18061) (PDF, EN, 950KB)
DIAMOND D-190 |
Broadband scanner antenna for high frequencies. Frequency range 100 - 1500 MHz! In the amateur bands 2m, 70cm, 23cm you can transmit with max. 50 watts. Top-processing, not cheap junk, chrome, stainless steel rods. Includes mast clamps, cable 10m, 2x PL connector. Length 84cm, weight 520g, diameter 36cm, yaw mount 25-50mm
Order No. | ||
---|---|---|
18063 | D-190 with PL-jack | 85.50 |
Desktop Discone |
The
Desktop Discone 18065 is one of the best solutions for indoor receiving antennas.
The antenna works with the well known Discone principle and covers a frequency
range from 25 to 2000 MHz. The heavy magnet base can be placed anywhere, for
example on the window ledge or on the heater. The antenna should be placed near
a window for best reception results. 4m coaxial cable with BNC connector are
included. Discone antennas work principally as a vertikal dipol. The Gain is 0
dBd or 2 dBi.
Order No. | ||
---|---|---|
18065 | Desktop Discone Scanner Antenna | 99.00 |
Mobile Discone |
The
mobile discone is a modified design of the desktop discone. The technical data
are the same like the desktop version, only the radials were left off and the
shaft is shortened. The antenna has become smaller and can now be used on the
car roof with the heavy magnetic base. 4m coaxial cable with BNC connectors are
included. Total length 64cm, 9cm diameter magnetic base, weight 800g.
Order No. | ||
---|---|---|
18066 | Mobile Discone Scanner Antenna | 49.00 |
Antennas for handheld scanner |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
||||||||||||||||||||
Model: | RH-951S | RH-795 | RH-799 | 17008.11 | 17008.10 | SRH-789 | ||||||||||||||||||||
Frequency range: | 120-1200 | 70-1000 | 70-1000 | 68-87 | 108-165 | 90-1100 | MHz | |||||||||||||||||||
Length retracted: | 35 | 19,5 | 19,5 | 35 | 35 | 20 | cm | |||||||||||||||||||
Length extended: | - | 115 | 113 | 80,5 | cm | |||||||||||||||||||||
Connector: | BNC | BNC | BNC | BNC | SMA | SMA | ||||||||||||||||||||
Remarks: |
flexible wideband antenna |
Telescopic antenna without knuckle |
Telescopic antenna with knuckle |
4m special
antenna |
Airband antenna |
Excellent for 4m |
||||||||||||||||||||
Order No. |
17017 39.00 |
17029 24.80 |
17030 26.20 |
17008.11 31.10 |
17008.10 26.90 17008.13 with BNC connector 24.90 |
17038 29.00 |
||||||||||||||||||||
|
Boni-Whip Active antenna |
Despite its small size (only about 14 cm short), this antenna has excellent receiving results at long-, medium- and short-wave range as well as for VHF up to 300 MHz. Already at low frequencies the Boni-Whip provids very good receiving results. Already applicable from 10 kHz, it is a good choice for the low-frequency interested.
The antenna is an ideal addition to all short-wave receivers and SDRs. It is supplied via connection cable, the required Bias-Tee is included. All antenna connections are BNC standard.
Antenna electronics is in a weather-proof housing. Because of the changeable beams, the antenna can be used with other or your own beams or wires.
![]() |
![]() |
||
---|---|---|---|
Frequency Range | 10 kHz - 300 MHz | ||
Power Supply | 9V - 15V | ||
Gain | up to +3dB | ||
Upper frequency limit (-1db) | 300 MHz | ||
2. order intercept point | > +55dBm | ||
3. order intercept point | > +32.5dBm | ||
Connectors | BNC |
Order No. | ||
---|---|---|
18067 | Boni-Whip Antenna | 119.00 |
Accessories Boni-Whip Active Antenna |
The Boni-Whip antenna is supplied without cable. This is understandable because everyone needs a different length. We offer several cables for this antenna. You need two cables: at first one longer cable between antenna and the DC injector (both sides BNC), and secondly a cable between the DC injector (BNC) and your radio.
Further you need a 12V (13.8V) DC power supply which can supply at least 300mA current. The connector is a DC coaxial connector on the DC injector, our article 42913. Optionally a mast mount bracket is offered, depending on the installation positon of the antenna (ref. 18067.MH). A surge protector (ref. 21049.BMF) can be useful for the Boni whip to protect the receiver. It should be used if a good grounding is available near the installation position. To protect the BNC connectors against rain we offer self vulcanizing tape, ref. 23065.
Order No. | ||
---|---|---|
18067.MH | Mast Mount for Boni-Whip | 16.00 |
21049.BMF | Surge Arrestor BNC male/BNC female | 40.50 |
42913 | DC coaxial connector | 2.60 |
23065 | Self vulcanizing tape, 1m | 13.50 |
Order No. | ||
---|---|---|
40403.50CM | H-155 LowLoss cable 0.5m, BNC/BNC | 10.30 |
40403.01 | H-155 LowLoss cable 1m, BNC/BNC | 10.90 |
40403.02 | H-155 LowLoss cable 2m, BNC/BNC | 12.10 |
40403.05 | H-155 LowLoss cable 5m, BNC/BNC | 16.00 |
40403.10 | H-155 LowLoss cable 10m, BNC/BNC | 22.30 |
40404.50CM | H-155 LowLoss cable 0.5m, BNC/PL | 10.30 |
40404.01 | H-155 LowLoss cable 1m, BNC/PL | 10.30 |
40404.10 | H-155 LowLoss cable 10m, BNC/PL | 22.50 |
40390.01 | H-155 LowLoss cable 1m, BNC/SMA | 20.50 |
Bonito Loop ML-200 |
The
Bonito ML-200 is a wide band active antenna for reception of long, medium and
short waves as well as the lower VHF band. The antenna is is characterized by a
small apcking size, low noise and excellent signal levels.
The ML-200 consists of a flexible, braided wire loop with large wire gauge. The loop is connected to the amplifier, both are installed by hanging the wire to the wall, into a window, in a tree or on another suitable supports. The amplifier is supplied over the coaxial cable (not included) from a supplied Bias-T. This Bias-T has connectors for an external supply voltage as well as a socket for a USB cable. The voltage can range from 5 to 15 V. The USB connector makes the antenna very well suitable for portable operations with a computer.
Despite the high amplification, the ML-200 has a very low noise level, as comparisions to other active antennas have shown. The antenna can be used from long wave (9 Khz) up to the lower VHF range of 200 MHz. The amplifier has a very high 3, order intercept point of +40dBm. This results in a very high distortion free blocking dynamic range. The amplifier is protected by a twofold overvoltage protection. With this protection the antenna not only survives a thunderstorm but can also be used in vicinity to transmitting antennas, for example in the garden of a radio amateur or on a sailing yacht.
With the small packing size and the USB power supply the ML-200 is very well suited to accompany you in a vacation. For example the antenna can be easily installed with two suction cup holders in a window. The coaxial cables are not supplied because most customers require different lengths. We provide several ready made cables, and can also manufacture a cable tailored to your requirements.
Packing size 20 x 20 x 5cm, weight 480 g. Connector on amplifier: BNC, HF-Connectors on Bias-T: 2x BNC. Requires additional DC cable or USB cable for power suply. Supply voltage from 5 to 15V DC, max. 40mA.
Order No. | ||
---|---|---|
ML-200 | Bonito ML-200 Mega Loop | 369.00 |
HF active antenna MFJ-1020C |
Active
antenna with preselector for 300kHz to 40MHz, ith adjustable amplification -5 to
15dB. Preselector with 6 overlapping ranges from 0,3 to 40MHz. To be used
indoors with the included whip antenna, or with an outdoor antenna (not included)
which is connected to the PL input jack. Power supply either with internal 9V
battery (not included) or with external 12V DC supply (not included). Size 5 x
15 x 13cm.
Order No. | ||
---|---|---|
MFJ-1020C | 126.90 |
Shortwave wire antenna |
Excellent wire antenna for shortwave listeners, consists of 20 or 40m PVC coated copper wire, two insulators, all required hardware plus a magnetic MTFT balun in weatherproof case. With this balun the antenna can be fed with any length of coax cable. With an additional tuner this antenna can be used for transmission in the range from 1.8 to 30MHz with 150W.
![]() |
![]() |
Order No. | ||
---|---|---|
11372.20 | with 20m copper wire | 85.00 |
11372.40 | with 40m copper wire | 94.00 |
Several revies of MTFT balun antennas from customers.
Antenna Splitter ASA-15 |
ASA-15: Antennea plitter for shortwave up to 70 MHz.
The antenna splitter ASA-15 distributes the signal of one receiving antenna to up to five receivers. Each of the five outputs has an individually selectable wideband amplifier with 12 dB gain. Further a 15dB attenuator is integrated in the input to reduce strong signals. The internal distribution is done with low noise amplifiers, preventing mutual influence of the outputs on each other. The selected configuration is shown with LEDs on the front panel. A power supply (12V/1A) is included.
This splitter is not suitable for transmitting.
![]() |
![]() |
ASA-15: Technical data | |
Frequency range: | 9 KHz - 70 MHz |
Power supply: | 11 - 15 VDC, 300mA |
Connectors: | PL female |
Gain: | 0 dB, Impedance: 50 Ω |
Enclosure: | solid aluminium case, rubber protected |
Size: | 200x200x55mm, Weight 1 Kg |
Output Isolation: | approx. 50 dB @ 30 MHz |
1dB Compression point at 7 MHz: | 15 dBm |
IP3 at 7 MHz: | 24 dBm |
Order No. | ||
---|---|---|
ASA-15 | Antenna Distributor 1:5 | 276.00 |
Antenna distribution 4:2 ASA-42 |
ASA-42: 4x2 antenna distributor for shortwave up to 70 MHz
With the ASA-42 antenna distributor the signal of four receiving antennas can be distributed to up to two receivers. The mutual influence of the receivers is reduced with wideband amplifiers, allowing to use multiple receivers on the same antenna. The selected configuration is displayed with LEDs on the front panel. A power supply (12V/1A) is included.
This distributor is not suitable for transmitting.
![]() |
![]() |
ASA-42: Technical data
Frequency range: | 9 KHz - 70 MHz |
Power supply: | 11 - 15 VDC, 300mA |
Connectors: | PL female |
Gain: | 0 dB, Impedance: 50 Ω |
Enclosure: | solid aluminium case, rubber protected |
Size: | 200x200x55mm, Weight 1 Kg |
Output Isolation: | approx. 50 dB @ 30 MHz |
1dB Compression point at 7 MHz: | 15 dBm |
IP3 at 7 MHz: | 24 dBm |
Order No. | ||
---|---|---|
ASA-42 | Antenna Distributor 4:2 | 249.00 |
Wideband Antenna Spliter/Combiner Diamond SS-500 |
Serves to connect two antennas to one receiver or vice versa - one antenna to
two receivers. This device contains a wideband transformation network which
combines both inputs and transforms the impedance. Further this networks
isolates both inputs against each other.
The insertion loss up to 200MHz is less or equal than 0.8dB, isolation between
both inputs is 30dB (@3-200MHz).
Due to the high isolation between the two inputs the SS-500 can combine any two
antennas, also with different frequency ranges, without one antenna shortening
the other antenna.
50 Ω impedance, SWR better than 2:1, Size 80x60x30mm, Connector 3x PL female.
This splitter/combiner is not suitable for transmission.
Technical
Data:
Frequency range | 0.5 to 500MHz |
Isolation | |
0.5 to 3MHz | > 18dB |
3 to 200MHz | > 30dB |
200 to 500MHz | > 17dB |
Insertion loss | |
0.5 to 3MHz | < 0.6dB |
3 to 200MHz | < 0.8dB |
200 to 500MHz | < 1.0dB |
Impedance | 50 Ω |
VSWR | < 2:1 |
Weight | 130g |
Size: | 80x60x30mm |
Order No. | ||
---|---|---|
22050 | Diamond SS-500 Splitter/Combiner | 60.10 |
Antenna splitter for 1090 MHz |
To
connect an ADS-B receiver with a wideband scanner or a flight radio receiver to
a common antenna.
The Splitter has two Outputs, one for a ADSB-Receiver (Radarbox, SBS-3 etc.) and
one more for 1,6-400 MHz, to any other receiver or scanner. The integrated
circuit ensures that the two outputs are combined to a correct impedance, on the
other side to avoid influencing each other are isolated.
The insertion loss is max. 0,5 dB, the Isolation between the 2 connectors is
minimum 45 dB.
50 Ω Impedance, SWR better 2:1, Size 80x60x30mm, Connector PL. This splitter/combiner
is not suitable for transmission.
Frequency Range | 1.6 to 400MHz | |
1090MHz | ||
Insertion Loss | < 0.5 | dB |
Isolation | > 45 | dB |
Impedance | 50 | Ω |
VSWR | < 2:1 | |
Size: | 80x60x30 | mm |
Weight | 130 | g |
Order No. | ||
---|---|---|
22051 | Diamond SS-AIR 1 Splitter | 78.00 |
SAT antenna TA-1 Turnstile |
Crossed
dipoles with one director element for reception of LEO sats in the frequency
range 137 to 152 MHz. Gain at high elevations 0 dB, at lower angles up to 4 dB.
50 Ω feed, SWR <2:1, total height 1300mm, diameter 1065mm, weight 2kg, Windload
90N @ 160km/h. Includes mast clamp. The antenna comes with 1 m RG-58 cable
attached, without connector. You need to install a suitable connector before use.
Order No. | ||
---|---|---|
18350 | TA-1 | 79.50 |
42005 | N connector, solder, RG-58 | 4.50 |
42203 | N connector, crimp, RG-58 | 3.90 |
42002 | PL connector solder, RG-58 | 1.50 |
42002.01 | PL connector solder, Teflon, RG-58 | 1.90 |
42070.58 | PL connector, watertight clamp, Teflon, RG-58 | 5.50 |
42503 | PL connector, crimp, RG-58 | 1.80 |
Download: Mounting Instructions TA-1 (PDF, DE, EN, 50KB)
KE-137 QFH Circular Antenna for NOAA and ACARS |
Circular
polarised antenna for reception of NOAA weather satellites on 137 MHz, or ACARS
transmissions on 135 MHz. The KE-137 is a quadrifilar helicoidal (QFH) antenna.
Due to the construction of the antenna the satellites are picked up at a very
low angle above the horizon, but equally well when right over the antenna. The
circular polarisation is required to compensate fluctations of the signal
strength. And the same applies to aircraft and their ACARS transmissions on 135
MHz, which can be received with the same antenna. The antenna is weatherproof
and intended for installation on a mast. A mast clamp for mast diameters from 25
to 65mm is included. Height c. 100cm, weight c. 1100g, connector PL female.
Order No. | ||
---|---|---|
18355 | Diamond KE-137 | 239.00 |
Alle prijzen zijn inclusief BTW., maar exclusief verzendkosten.
Tussentijdse prijswijzigingen en typefouten voorbehouden.
Fabrikanten kunnen specificaties en uitvoeringen wijzigen.